SyncScan incorporates Phased Array, TOFD and thickness measurement functions into one compact unit, which can save your cost for Phased Array and TOFD.
SyncScan can minimize your cost for Phased Array and TOFD inspection. 

• IP rate: IP65
•  Light Weight: 3.75 kg with battery
•  Large touch screen: 8.4" LCD with resolution 800×600 pixels
•  Upgradeable from conventional UT to phased arrayTOFD thickness measurement with powerful & complete optional software functions.

Upgradeable
One-hand Operation
Flat Weld Simulation
Smart Test Wizard

• IP 66 with compact size: 198 (W)* 128 (H) *52 (L) mm
• Light weight: 0.9kg only, including battery
• 5.7" LCD with high resolution 640×480 pixels
• Adjustable pulse width, negative square wave transmission up to 350V.
• Operating frequency range: 0.5~20MHz, multiple steps of wide broadband and narrow-band for selection.
• Easy operation: only a few buttons, intuitive interface and logical menu, support right/left-hand operation, outdoor mode.

Conventional UT functions:

• Weld, plate and forging test wizards are available.
• Peak memory, DAC curve, AGC (Auto gain control), video record makes convenient flaw inspection.
• Optional functions: B-Scan, TCG, FFT (probe spectral analysis), CSC (curved surface correction), flat weld simulation, crack height measurement, BEA(backwall echo attenuator), AWS, API 5UE.

Thickness measurement functions:

• A-scan thickness measurement(echo to echo mode, through coating measurement)
• Auto-search, velocity measurement, alarm and dataset management.
• Optional functions: CoatMode, B-Scan, Multilayers, Vpath, TDG and temperature compensation.

Norm compliant: EN12668-1: 2010/ASTME317(for UT) and EN15317-2007(for TG).

PA Crawler for Small Pipe Welds
The low profile crawlers LPS‐01 and LPS‐02 are used to perform circumferential weld inspection on small diameter pipes, with OD ranging from 20.32‐114.3mm (0.84‐4.5 inch).

•  Compact, lightweight and portable.
•  IP68, waterproof, rust‐free and CE‐compliant.
•  Operates within small clearance, perfect for hard‐to‐reach area inspection.
•  Provide stable and constant pressure around the pipe full circumference.
•  Positive and reverse inspection with high reproducibility and good coupling.
•  Two inspection methods: one‐side and dual‐side inspection.

The low profile crawlers LPS‐07 and LPS‐08 are used to perform circumferential weld inspection on medium diameter pipes, with OD ranging from 100‐300mm (3.94‐11.81 inch).

• Compact, lightweight and portable.
• IP68, waterproof, rust‐free and CE‐compliant.
• Operates within small clearance, perfect for hard‐to‐reach area inspection.
• Provide stable and constant pressure around the pipe full circumference.
• Positive and reverse inspection with high reproducibility and good coupling.
• Two inspection methods: one‐side and dual‐side inspection.

The crawler LPS‐08, with TOFD probes and wedges are also available for TOFD inspection for medium pipe welds, with OD ranging from 100‐300mm (3.94‐11.81 inch).

• Narrow pulse TOFD probe with small crystal to reduce blind zone.
• Curved wedges with short flank for good coupling.
• No requirement on defect orientation, high detection rate.

The MPS-01A is suitable for PA immersion testing for corrosion on pipes with OD≥100mm and plate.

•  Compact: 140x110x80 (mm), 1.8kg.
•  IP68, waterproof, rust-free and CE-compliant.
•  Mouse shape design for easy control.
•  Magnetic wheels for stable operation.
•  Consumable gasket fits tightly to the surface of the workpiece.
•  Bubbles discharge design ensure coupling not affected even by a few bubbles.
•  Wide coverage of sound beams to improve testing efficiency.

The MPS-02 is used for PA Inspection on corrosion. It can be used for PA testing on small&medium areas, immersion pipeline and even for scanning in any direction in two-dimensional space.

•  IP68
•  Suitable for pipe OD≥100mm and plate with wall thickness ≥4mm
•  Wide coverage, high density C-scan, double crystal and PA focusing
•  Real-time display of probe position and statistical information
•  Customizable probe holder size, suitable for a variety of probe types
•  Magnetic or rubber wheels for your option
•  Mouse shape design for easy control
•  Only a little water to achieve good coupling on flat or small curvature surface

Phased Array crawler PES-02 is compact flexible and easy to operate.It is suitable for phased-array single probe (with wedge) to perform ultrasonic phased-array testing on girth weld or longitudinal weld of flat butt welds pressure vessels or pipes (diameter > 60mm).

•  Waterproof (IP68)
•  Compact size
•  Aluminumalloy construction:withstand the harshest environments.
•  High encoder resolution: 0.05mm/step.
•  Compatible with long and short pivot arms to achieve flexible application.

The Phased Array and TOFD crawler PTS-P05 is compatible with PA or TOFD ultrasonic flaw detector. It is suitable for phased array or TOFD testing on plates and pipe work pieces.

• The magnetic wheels can be attracted to the workpieces for easy operation.
• Spring arm structure which follows the tested surface maintaining good coupling between the wedge and the tested work piece.
• The probe fixed arm spacing is adjustable which can be installed with wedges of various specifications to meet specific needs.
• The position of the probe holder can be adjusted to the actual testing needs convenient and flexible.

The TOFD crawler TSB-1-P05 and TSB-2-P05 are compatible with TOFD ultrasonic flaw detector as well as TOFD wedges. They are suitable for TOFD testing onplate-type work pieces.

• The magnetic wheels can be attracted to the work piece for easy operation.
• Spring guide rail structure, which enables the probe holder to move up and down along the tested surface, maintaining good coupling between the wedge and the tested work piece.
• The rolling direction of the wheels is adjustable for transverse scan and vertical scan.

The Phased Array and TOFD crawler UHTS-X02 is compatible with PA or TOFD ultrasonic flaw detector. It can be folded in the center for longitudinal weld and unfolded for girth weld enabling the crawler have better coupling stability to work on smaller pipes suitable for phased array or TOFD testing on plates and pipe workpieces (with diameter larger than 500mm).

•  Standard configured as two channels TOFD crawler
•  Support Phased Array probes
•  Support up to 3 pairs of probe holders simultaneously.
•  The magnetic wheels can be attracted to the tested work piece for easy operation.
•  Spring guide way structure which follows the tested surface maintaining good coupling between the wedge and the tested work piece.

CPS-01

The CPS-01 is suitable for circumferential weld inspection on long-distance pipeline with OD 1000-1300mm (39.38-51.18 inch).
Dual-side PAUT & PAUT+TOFD inspection for selection.

•  IP68, waterproof, rust-free and CE-compliant.
•  Double wheel chains straddle the weld to ensure stabling.
•  Easy buckle design for quick change links to adapt to different pipe diameters.
•  Chain plus guide rail design to keep straight track and ensure the testing accuracy.
•  High elastic rubber wheels to achieve stable probe movement.
•  Flexible structure, the truss can be setup without disassembling the chain.
•  Manual or automatic water irrigation device to maintain water output for good coupling.

CPS-02

The CPS-02 series is suitable for circumferential weld inspection on medium & large pipe welds with OD 100-1000mm (3.94-39.37 inch) and higher wall thickness.
3 Models for different configurations, up to 2 PA+2 ch-TOFD.

•  IP68, waterproof, rust-free and CE-compliant.
•  High-strength aluminum alloy material, strong and lightweight.
•  Double wheel chains straddle the weld to ensure stabling.
•  Easy buckle design for quick change links to adapt to different pipe diameters.
•  High elastic rubber wheels to achieve stable probe movement.
•  Flexible structure, the truss and crossbeam can be setup without disassembling the chain.
•  Manual or automatic water irrigation device to maintain water output for good coupling.

The CTS-30A/CTS-30B ultrasonic thickness gauge, adopts micro-processor technology and advanced manufacture process design, can do measurementof thickness and acoustic velocity on metal and many different materials.

•  100×65×25 (mm), 140g (with batteries)
•  ≥30 hours operation time
•  Auto and user-defined calibration
•  Various measurement arithmetic: standard/ minimum/ average/ difference
•  Up to 5000 sets of measurement data and 100 sets of parameter data
•  EN15317 compliant

Compared with CTS-30A, the CTS-30B model has more advanced functions, such as:
√ Fast Scan
√ Two-point calibration
√ Multi-probe selection

The CTS-30C is an entry-level & cost-effective thickness gauge, especially good for thru-coating thickness measurement on painted/ coated thin wall pipe in machinery,chemical, ship building, aeronautical and aerospace industries.

•  Tiny and low consumption
•  Measurement function: Standard/ minimum/ average/ difference/ fast scan
•  Large storage, data can be transferred to PC and generated as a TXT file.
•  EN15317 compliant

Upgradeable
One-hand Operation
Flat Weld Simulation
Smart Test Wizard

• IP 66 with compact size: 198 (W)* 128 (H) *52 (L) mm
• Light weight: 0.9kg only, including battery
• 5.7" LCD with high resolution 640×480 pixels
• Adjustable pulse width, negative square wave transmission up to 350V.
• Operating frequency range: 0.5~20MHz, multiple steps of wide broadband and narrow-band for selection.
• Easy operation: only a few buttons, intuitive interface and logical menu, support right/left-hand operation, outdoor mode.

Conventional UT functions:

• Weld, plate and forging test wizards are available.
• Peak memory, DAC curve, AGC (Auto gain control), video record makes convenient flaw inspection.
• Optional functions: B-Scan, TCG, FFT (probe spectral analysis), CSC (curved surface correction), flat weld simulation, crack height measurement, BEA(backwall echo attenuator), AWS, API 5UE.

Thickness measurement functions:

• A-scan thickness measurement(echo to echo mode, through coating measurement)
• Auto-search, velocity measurement, alarm and dataset management.
• Optional functions: CoatMode, B-Scan, Multilayers, Vpath, TDG and temperature compensation.

• Norm compliant: EN12668-1: 2010/ASTME317(for UT) and EN15317-2007(for TG).

Superior Features

•  Support transmit and receive longitudinal waves for inspecting welds in grainy materials.
•  Better penetration and near-surface resolution.
•  The "pseudo‐focus effect" enables the adjustable focal area for wide coverage.
•  Excellent focusing effect and signal-to-noise ratio.

Testing Results 4.0DM16×2-1.0-3.0 probe for testing austenitic stainless steel with thickness 15mm

SIUI can provide PA probes with different connectors compatible with PA equipments from other manufacturers.

Universal Probes
Small/ Medium/ Large-Size & Low Frequency Probes

Superior Features:

• Sound Beam angle,focusing and scan step can be electronically controlled;
• Wide scan coverage can be achieved by one single probe;
• Replaceable angle wedge and delay block, with customizable surface curvature;
• Array pitch and elevation can be customized.

SIUI can provide a series of TOFD probes compatible with different TOFD flaw detectors;
Customization of TOFD probes and wedges with different specifications.

Normal Probe
Mainly used for testing defects parallel to or slightly tilted against the test surface (e.g.steel plate)

Replaceable Membrane Normal Probe
Mainly used for inspecting container flaws as well as flaws parallel to the inspected surface, applicable for checking coarse and slightly-curved surfaced objects.

Replaceable Delay Line Normal Probe
Mainly used for inspecting flaws parallel to/ near to the inspected object surface, applicablefor inspected objects with sharp edge.
If the delay line is made ofhigh-temperature material, it can also inspect high-temperature objects.

Angle Probe (Transverse Wave)
Mainly used for testing defects perpendicular to or obviously tilted against the test surface (e.g.welding line testing).

Angle Probe ( Longitudinal Wave )
Mainly used fortesting defects perpendicular to or obviously tilted against the test surface (e.g.welding line testing).

Thickness Gauge Probe
Mainly used for measuring work piece thickness.

Dual-Element Angle Probe
Mainly used for testing defects tilted against the test surface or perpendicular to the test surface.

Dual-element Normal Probe
Mainly used for testing defects parallel to or slightly tilted against the test surface (e.g.steel plate);
Much more appropriate for detecting near surface flaws than normal probes.

Immersion Probe
Mainly used in situations where the work piece and the probe do not contact directly. 
It is suitable for testing work piece with rough surface and automatic testing required to increase scanning speed and shorten testing time.

Variable-angle Probe
The reflection angle can be adjusted to meet different requirements.

Surface Wave Probe
Mainly used for surface defect testing and also for surface crack depth testing.

Spot-Weld Probe
Straight-beam probe with soft protective membrane, using water column as water delay coupling, so as to achieve optimal coupling between the probe and spot weld surface. 
Especially good for spot-weld testing on thin plates of automotive industry.