4/5-Step Block
	Specifications: ASTM E797 Calibration Function: Straight Beam: thickness and linearity calibration, thickness gauging.
Calibration block No.1(V1)
	Specifications: ISO2400-2012 Calibration Function: Calibration of shear and compression wave probes. Checking beam angle, emergent point and resolution.Calibration of time base and gain settings. *We can provide V1 calibration block based on ISO2400-2012, BS2704, ASTM E164, ISO2400-1972E, AWS D1.1/D1.1M and AS 2083.
Calibration Block No.2 (V2)
	Specifications: ISO7963:2010 Calibration Function: Small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain, engraved reference mark scales from 35 to 75 degrees. *We can provide V2 calibration block based on BS2704 and ISO 7963.
Calibration Block No.3 (V3)
	Calibration Functions: For calibrating ultrasonic flaw detection equipment in both laboratory and on-site conditions. This block is intended to function as a more compact and light-weight alternative to V1 or IIW-Type Test Blocks. Includes 25mm, 50mm, and 100mm radii, (2)3.0mm diameter through holes, engraved reference mark scales, and a 0.4mm wide * 2.5mm deep slot.
Phased Array Test Block Type A
	Specifications: ASTME2491-2013 Calibration Functions: The Phased Array “Type A” Calibration Block is used during the initial setup and calibration of a phased array ultrasonic unit. It can be used to perform tasks such as beam angle verification, calibration for wedge delay, sensitivity calibration, performing DAC/TCG for thickness up to 50 mm, and crack sizing.
Phased Array Test Block Type B
	Specifications: ASTM E2491-2013 Calibration Function: The Phased Array “Type B” Calibration Block is used as baseline block to determine long-term instrument performance changes, generate DAC curves, and evaluate linear/ angular resolution, focusing ability and beam steering capability.
PAUT IIW Test Block
	Specifications: ISO 19675 Calibration Function: Probe index, beam angle, beam squint angle, linearity of time base, calibration of time base, linearity of attenuator, linearity of screen height, pulse duration, measurement of dominant frequency, signal-to-noise ratio (SNR,) wedge delay, assess for grating lobes, active element assessment, sensitivity equalization for E-scans, sensitivity equalization for S-Scans, plotting check, element assignment, anisotropy assessment.
Miniature Angle Beam (ROMPAS) Calibration Block
	Specifications: ASTM E164-2013 Calibration Function: Straight Beam: distance angle beam, index point, sound path angle (30°-70°).
DSC Distance/ Sensitivity Calibration Block
	Specifications: ASTM E164-2013 Calibration Function: Straight Beam: distance, amplitude. Angle Beam: index point, sound path angle (45°-70°),distance, sensitivity.
GSSeries Calibration Block(Set of 7)
	Specifications: NB/T47013.3-2015 Calibration Function: GS Series Calibration Block is used for ultrasonic testing of circumferentially butt joints (type II welded joints) for pipes (applicable OD range 20-500mm).
DC Distance Calibration Block
	Specifications: ASTM E164-2013 Calibration Function: Straight Beam: distance, amplitude. Angle Beam: index point, distance. *We can provide DC calibration block based on ASTM E164, AWSD1.1/D1.1M.
SC Sensitivity Calibration Block
	Specifications: ASTM E164-2013 Calibration Function: Angle Beam: sound path angle (45°, 60°, 75°), sensitivity. *We can provide SC calibration block based on ASTM E164, AWSD1.1/D1.1M.
DS Distance/ Sensitivity Calibration Block
	Specifications: AWS D1.1/D1.1M-2015 Calibration Function: Straight Beam: distance, horizontal linearity, sensitivity.
RC (AWS) Resolution Calibration Block
	Specifications: AWS D1.1/D1.1M-2015 Calibration Functions: Angle Beam: resolution (45°, 60°, 70°).
IOW Beam Profile Block
	Specifications: API RP 2X-2004 Calibration Functions: Angle Beam: beam profile (45°, 60°, 70°), probe angle. *We can provide IOW calibration block based on API RP 2X, BS 2704, AS 2083.
ASME Basic Calibration Blocks
	Specifications: ASME BPVC-V (2015) Calibration Functions: Used for establishment of primary reference responses for UT examination of welds.
ASME Basic Calibration Blocks for Pipe
	Specifications: ASME BPVC-V (2015) Calibration Functions: The basic calibration block fabricated for customer supplied section of pipe of the same diameter, schedule, heat treatment and material type as the material being examined.
ASTM Area/ Amplitude (Set of 8)
	Specifications: ASTM E127-2015 or ASTM E428-2008 Calibration Functions: Determining relationship comparisons of flaw size and echo amplitude.
ASTM Distance/ Area Amplitude (Set of 10)
	Specifications: ASTM E127-2015 or ASTM E428-2008 Calibration Functions: Determining relationship comparisons of flaw size and echo amplitude.
ASTM Distance Amplitude (Set of 19)
	Specifications: ASTM E127-2015 or ASTME428-2008 Calibration Functions: Comparisons of distance amplitude relationships.

The post Calibration block appeared first on NDT Service.

High Temperature Wedge

Curved Wedge

Irrigation Wedge

TOFD wedge
Non-irrigation Wedge

Irrigation Wedge

Probe Cable

SIUI provides various of probe cables to be compatible with probes.
There are different kinds of cable connectors for your selection,such as BNC, LEMO 01,LEMO 00, Microdot, UHF etc.

Probe Test Report

Probe test reports are available as option.

Storage Boxes

Storage boxes are available.

The post Accessories appeared first on NDT Service.

Normal Probe
	Mainly used for testing defects parallel to or slightly tilted against the test surface (e.g.steel plate)
Replaceable Membrane Normal Probe
	Mainly used for inspecting container flaws as well as flaws parallel to the inspected surface, applicable for checking coarse and slightly-curved surfaced objects.
Replaceable Delay Line Normal Probe
	Mainly used for inspecting flaws parallel to/ near to the inspected object surface, applicablefor inspected objects with sharp edge. If the delay line is made ofhigh-temperature material, it can also inspect high-temperature objects.
Angle Probe (Transverse Wave)
	Mainly used for testing defects perpendicular to or obviously tilted against the test surface (e.g.welding line testing).
Angle Probe ( Longitudinal Wave )
	Mainly used fortesting defects perpendicular to or obviously tilted against the test surface (e.g.welding line testing).
Thickness Gauge Probe Mainly used for measuring work piece thickness.
High Temperature Probe (Up to 200℃)
Twin Crystal Probe
Delay Line Probe
Angle Probe With Replaceable Wedge
Dual-Element Angle Probe
	Mainly used for testing defects tilted against the test surface or perpendicular to the test surface.
Dual-element Normal Probe
	Mainly used for testing defects parallel to or slightly tilted against the test surface (e.g.steel plate); Much more appropriate for detecting near surface flaws than normal probes.
Immersion Probe
	Mainly used in situations where the work piece and the probe do not contact directly. It is suitable for testing work piece with rough surface and automatic testing required to increase scanning speed and shorten testing time.
Variable-angle Probe
	The reflection angle can be adjusted to meet different requirements.
Surface Wave Probe
	Mainly used for surface defect testing and also for surface crack depth testing.
Spot-Weld Probe
	Straight-beam probe with soft protective membrane, using water column as water delay coupling, so as to achieve optimal coupling between the probe and spot weld surface. Especially good for spot-weld testing on thin plates of automotive industry.
Custom Ultrasonic Probe
	SIUI can provide custom ultrasonic probes according to specific requirement.

The post UT Probes appeared first on NDT Service.

LEMO 00 Connector

Microdot Connector

The post TOFD Probes appeared first on NDT Service.

Superior Features

• Support transmit and receive longitudinal waves for inspecting welds in grainy materials.
• Better penetration and near-surface resolution.
• The “pseudo‐focus effect” enables the adjustable focal area for wide coverage.
• Excellent focusing effect and signal-to-noise ratio.

Testing Results

• 4.0DM16×2-1.0-3.0 probe for testing austenitic stainless steel with thickness 15mm

• 2.25DM7×4-2.71-3.0 probe for testing austenitic stainless steel with thickness 40mm

The post Dual Matrix Array Probes for Welds appeared first on NDT Service.

SIUI can provide PA probes with different connectors compatible with PA equipments from other manufacturers.

Universal Probes
Small/ Medium/ Large-Size & Low Frequency Probes
	Superior Features: Sound Beam angle,focusing and scan step can be electronically controlled; Wide scan coverage can be achieved by one single probe; Replaceable angle wedge and delay block, with customizable surface curvature; Array pitch and elevation can be customized.
Immersion Linear Array Probe
	Superior Features: Sound Beam angle,focusing and scan step can be electronically controlled; Wide scan coverage can be achieved by one single probe;
Immersion Curved Array Probe
	Superior Features: Adopt immersion method for inspection; Sound Beam angle,focusing and scan step can be electronically controlled; Wide scan coverage can be achieved by one single probe; The curvature radius of curved probes can be customized;
Small-size immersion curved array probe
Large-size immersion curved array probe
High Penetration Probes
	Superior Features: Good resolution and high penetration; Replaceable angle wedge and delay block, with customizable surface curvature; Array pitch and elevation can be customized.
Small Footprint Probe
	Superior Features: Compact size; Cable connectorcan come out from either the side or the top; Replaceable angle wedge and delay block, with customizable surface curvature; Array pitch and elevation can be customized.
Custom Phased Array Probes SIUI can produce custom phased array probes to suit specific applications and geometries.
Flexible Probe
	Superior Features: Soft structure can be shaped to have better coupling stability to work on various work piece surface shape, especially curved surface. With thickness less than 3.0mm, the probe can be used for limited space inspection.
Wheel Phased Array Probe
Low-profile Probe
	Superior Features: With theLow-profile PA probe, the probability of small defects detection in small pipe can be increased.
Matrix Array Probe
	Superior Features: Sound Beam angle,focusing and scan step can be electronically controlled; Two types for selection: flat or curved; Hard-to-reach area can be inspected; Immersion matrixarray probe can be customized.
Near-Wall Probe
	Superior Features: Small blind zones in both edges; Larger scan coverage can be achieved.

The post PA Probes appeared first on NDT Service.